Techengy Materials / Doors
A door that suits the room it opens into.
WPC interior doors are built around a wood-plastic composite core rather than solid timber. Choose the construction first, then the surface, the frame and the hardware.
Specification confirmed in writing for each project.
Three ways these doors are built.
The same look can be sold three different ways, and the difference is in the build rather than the photograph. Decide which one suits the opening before you choose a colour. A composite door is made from resin, wood fibre and polymer material, extruded under heat and pressure into a panel — that is why it behaves differently from timber in a humid building.
Two of these families are also supplied as parts rather than as complete doors. A door skin — flush or 3D-moulded — is sold on its own to re-face a blank you already have, which is how a run of doors gets a new face without every leaf being replaced.
More than one kind of door.
The families below come from the manufacturer's own catalogue, and the pages are shown as published — finishes, model references and mouldings included. Techengy quotes the construction and finish that fit your opening, and confirms availability at that point.

WPC skin doors
A composite skin pressed over a core. Moulded and flat designs, and the widest decorative choice of the three families.

Full-WPC doors
Solid composite through the leaf rather than a skin over a blank. Heavier in the hand and the usual choice where the door is handled constantly.

Assembly doors
Frame, leaf and trim supplied as one set, so the door and its opening are made to fit each other instead of being brought together on site.

Frames, architraves and glass
Door frames and architraves, flush and concealed variants, and aluminium glass doors for openings that should carry light.
The system does not stop at the door. Wall panels, skirting and decoration lines are produced in the same material, so a corridor, a lobby or a bathroom run can be finished as one system rather than three separate ones that have to be matched afterwards.
The finish is a separate decision.
A WPC door reaches you one of two ways. Either a PVC film is laminated onto the composite panel — a woodgrain or solid-colour layer with matching edge banding — or the panel is painted, which is how flat and uniform colours are produced. The same door style is offered in both, so a run of doors can be colour-matched to a room rather than chosen from a swatch book.
Decorative lines pressed into the leaf are a design choice, not a strength rating: a shallow groove, a panel moulding and a flush face all come from the same construction underneath.
Decided together, not after.
The frame is where most door installations go wrong. These systems supply the frame, architrave and trim as part of the door set, with concealed and flush options for openings where the frame should disappear into the wall.
Frames are catalogued by type — this system runs A, B, D and E, alongside a separate architrave range — and the difference between them is the profile and the way the leaf meets the jamb, not the strength of the frame. Which type suits your wall construction is settled at survey, before the leaf is machined.
Assembly sets can also be cut to the opening during installation, which is what makes them practical where a reveal is out of square or the structural opening was never built to a standard size.
Handles, locks, hinges and the machining for them are part of the order too — hinge position and lock cut-out are made to your specification, and door thickness and leaf width have to be settled before any of it is drilled.
See it in context.
Photography helps describe the scale and the visual effect of matched door sets. We confirm available construction, finish and hardware for your project separately.
Matched but not identical
A pale and a warm tone run along the same corridor. Tone variation across a run of doors is a selection question, not a defect.
Doors as part of the wall
Flush doors set into a decorated lobby wall. Survey first, because the surrounding finish decides the trim.
What the maker claims, and what we confirm.
WPC doors are marketed on moisture tolerance and termite resistance. Rather than repeat that as our own promise, here is what the manufacturer publishes about its board — and the questions worth putting to them before you order.
The manufacturer's published figures
- Formaldehyde emission
- measured 0.006 mg/m³ against an ENF grade limit of ≤0.025 mg/m³
- Water content
- measured 0.7% against a ≤2.0% standard
- Water absorption expansion
- measured 0.2% against a ≤0.5% standard
- Flexural elastic modulus
- measured 1998 MPa against a ≥1800 MPa standard
- Surface hardness
- measured 76HD against a ≥60HD standard
These are the board manufacturer's own laboratory figures for its WPC material, reproduced here as published. They are not Techengy measurements and not a Techengy warranty.
What we put in writing instead
- The construction you are buying — skin, hollow or full composite.
- The exact panel thickness and leaf size against your measured opening.
- The finish system, colour reference and edge treatment.
- Frame type, architrave and how the door meets the wall.
- Hardware schedule and the machining done at the factory.
- Which certificates exist, and which of them cover your order.
If a supplier's claim matters to your project — a fire rating, a certificate, a specific country-of-origin document — say so at enquiry stage and we will tell you whether the paperwork exists before you commit.
Send us the opening, not just the picture.
Give us the opening size, how many doors, the wall construction, the direction they open and the tone you have in mind. Add the project location and a photograph if you have one. Those details are enough for us to come back with the right door type and a written quotation.
WPC construction, finish and hardware are confirmed in writing for each order.